Sleeve sensor with temperature measuring transducer (cable temperature measuring transducer) THERMASGARD® HFTM

Display

IP protection class

output model

output

Product group: WG01B

Sleeve sensor with temperature measuring transducer (cable temperature measuring transducer) THERMASGARD® HFTM

Calibratable THERMASGARD® HFTM temperature measuring transducer with sleeve sensor with eight switchable measuring ranges, continuous output, housing made of impact resistant plastic with quick-release screws, optionally with/without display, with cable gland or M12 connector according to DIN EN 61076-2-101.

The temperature transmitter with remote sensor serves to detect temperatures in liquid and gaseous media, e.g. if installed in a thermowell or as a duct sensor. A direct, permanent use in liquids is possible in combination with our THE thermowells (accessory).The sensor is factory-calibrated and can be fine-tuned to ambient conditions by an expert.

Available configurations

Artikelnummer	Bezeichung
1101-1151-0219-920	THERMASGARD® HFTM-U
1101-1151-2219-920	THERMASGARD® HFTM-U LCD
1101-1152-0219-920	THERMASGARD® HFTM-I
1101-1152-2219-920	THERMASGARD® HFTM-I LCD
1101-115E-0219-920	THERMASGARD® HFTM-A
1101-115E-2219-920	THERMASGARD® HFTM-A LCD
1101-6161-0219-920	THERMASGARD® HFTM-SD-U
1101-6162-0219-920	THERMASGARD® HFTM-SD-I
2001-2111-1100-001	THERMASGARD® HFTM-U Q
2001-2111-2100-001	THERMASGARD® HFTM-I Q
2001-2112-1100-001	THERMASGARD® HFTM-U Q LCD
2001-2112-2100-001	THERMASGARD® HFTM-I Q LCD

Power consumption

< 1,0 W/ 24 V DC
< 2,2 VA/ 24 V AC

Deviation of humidity

typically ± 0.2 K at +25 °C

Sensor

Pt1000, DIN EN 60751, class B

Sensor protection

sensor sleeve, stainless steel V4A (1.4571), Ø = 6 mm,
nominal length NL = 50 mm (other dimensions optionally available)
cable entry stamped (optionally rolled)

Connection type

2- or 3-wire connection

Measuring ranges

multi-range switching with 8 switchable measuring ranges,
see table (other ranges optional)
with manual zero point correction (± 10 K)

Accuracy

typically ± 0.2 K at +25 °C

Ambient temperature

Measuring transducer –30...+70 °C

Insulating resistance

100 MΩ,
at +20 °C (500V DC)

Sensor protection

stainless steel, 1.4571, V4A, Ø = 6 mm,
nominal length (NL) = 50 mm
(other dimensions optional)
cable entry stamped (optional rolled)

Electrical connection

0.14 - 1.5 mm²
via terminal screws on circuit board

Cable connection

cable gland, plastic (M 16 x 1.5; with strain relief, exchangeable, max. inner diameter 10.4 mm) or
M12 connector according to DIN EN 61076-2-101 (optional on request)

Cable gland

M 16 x 1.5, including strain relief, exchangeable,
max. inner diameter 10.4 mm

sensor cable

Silicone, SiHF, 2 x 0,25 mm²; cable length (KL) = 1.5 m
(other lengths and jacket materials, e.g. PTFE or
glass fibre with steel mesh, available on request)

Permissible air humidity

< 95 % RH, non-precipitating air

Protection class

III (according to EN 60 730)

Protection type (sensor)

IP 65 (according to EN 60 529) sleeve humidity-tight (standard)
IP 68 (according to EN 60 529) sleeve water-tight (optional)
IP 54 (according to EN 60 529) with glass fibre cable (optional)

Standards

CE conformity,
electromagnetic compatibility according to EN 61326,
according to EMC Directive 2014/ 30/ EU

Operating instructions

Catalogue page EN

CE - Declaration of Conformity

UKCA - Declaration of Conformity

CAD data

Tender text