Construction progress of the Giga factory for sensor technology

The structural work on the production halls and offices at our new location in Nuremberg, Germany is nearing completion. Construction is progressing according to plan, so we are well positioned for the future and the increasing demand for our sensors.

Watch the video

Groundbreaking ceremony for significant growth

The office and manufacturing space alone at the new S+S location in Nuremberg will be expanded to 8,600 m² in order to meet the increasing demand for advanced sensor devices.

Watch the video

With Giga factory for sensors to become the #1 on the market

On a total area of over 14000 square meters, the new S+S company headquarters is being built in the north of Nuremberg.

Watch the video

Specialists in pressure

Multi-range measuring transducers for pressure, differential pressure and volume flow

PREMASGARD 211x / 212x

Efficient, convenient and network-enabled

Elegant appearance, touch-operated interface, large display, and Modbus-compatible


Multi-funtional duct sensor

For humidity, temperature, pressure, differential pressure and volume flow for monitoring and controlling heating, ventilation and air-conditioning systems

PREMASGARD® 814x-Modbus

Satisfied customers drive our business

An overview of our references

Learn more

Electronic frost protection monitor

2-phase thermostat with continuous and switching output for reliable prevention of frost damages and freezing


Für jede Anwendung die richtige Lösung [Translate]



Item No. 1801-4280-3000-000
EAN 4 251325 618265

The room radio sensors of the radio bus system KYMASGARD® 9000 are maintenance-free radio transmitters that function without batteries. Energy generation is effected by conversion of indoor room light into electric energy by means of a solar generator. If the ambient light is too low for power generation, the sensors can optionally be powered by two AAA batteries (not included). These sensors are used to detect the indoor climate and the setpoint values, and to transmit the recorded values to radio actuators and radio signal receivers/ gateways via radio signals. The following device configurations are available:

The room sensor KYMASGARD® RFTM-FSE is used to measure room temperature and room humidity.

The room control unit KYMASGARD® RFTM-FSE-ST is used to measure room temperature and humidity, and to display and set the setpoint for temperature. The setpoint is set directly on site using touch buttons.

The room sensor KYMASGARD® RFTM-LQ-FSE is used to measure room temperature, room humidity and air quality (VOC = Volatile Organic Compounds).

The room sensor KYMASGARD® RFTM-BW-FSE is used to measure room temperature, room humidity and the movement (or presence) of persons.

Optional accessories include the wall holder WH-3100 and the stand holder SH-3110, which enable them to be used as table-top units.

327,49 € net
Operating range, humidity 0...100 % r. H.
Deviation of humidity typical ± 2.0 % r. H. (20…80 % r. H. ); at + 25 °C, otherwise ± 3.0 % r. H.
Operating range, temperature 0...+40 °C
Temperature deviation typically ± 0.2 K at +25 °C
Measuring range, VOC 0...100 % air quality; with reference to calibration gas
Measuring accuracy, VOC ± 20 % of final value (referred to calibrating gas)
Operation Energy generation by solar cell,
batteryless, maintenance-free (optionally battery-operated)
Radio technology EnOcean protocol, modulation ASK, 868 MHz,
transmission power max. 10 mW, telegram type 4BS
1 temperature, 1 humidity, 1 setpoint,
1 air quality (VOC), 1 motion/presence
Radio transmitter module EnOcean Dolphin
Measurand acquisition adjustable, every 1s/ 10 s/ 100 s
Transmission interval adjustable, typically every 100 seconds,
or at any measuring value change,
status telegram approximately every 16 minutes
Range of coverage indoors typically 30 - 100 m, outdoors up to 300 m
Ambient temperature –5...+55 °C
Storage temperature –25...+60 °C
Housing plastic, material ABS,
colour pure white (similar to RAL 9010)
Dimensions Ø 88 mm, height 18 mm
Installation Wall-mounted or free-standing using accessories
Permissible air humidity 0…90 % r.H., non-precipitating air
Protection class III (according to EN 60 730)
Protection type IP 30 (according to EN 60 529)
Standards CE conformity according to EMC directive 2014/ 30/ EU
and according to R&TTE directive 2014/ 53/ EU

S+S Regeltechnik - Benefits to the power of five

Learn more

S+S Regeltechnik News

Exhibition Newsshow all


Light + Building 2020 – S+S Regeltechnik will be there
27.09. - 02.10.2020

Hall 9.1 | Booth A84
Be our guest at the world's leading trade fair for light, design and intelligent...

Overview of all exhibition dates

Product Newsshow all


HYGRASREG® TW ⁄ KW ⁄ KW-SD - Dew point and condensation control switches

These typical high-quality products from S+S feature innovative measuring, enclosure and connection...


THERMASGARD® TM65-Modbus -T3 - Calibratable immersion, screw-in or duct temperature measuring transducer

Patented high-quality product (patented immersion sensor, DE 10 2012 017 500.0) – basic device with...

Exhibition News

Light + Building 2020 | Frankfurt am Main | 27.09. - 02.10.2020


Newsletter Subscription

Stay always informed about our products and news from S+S Regeltechnik