- New
- Sale
- Temperature
- Humidity
- Pressure
- Light Intensity & Motion
- Air Quality
- Flow
- Modbus | Wireless Modbus
- Room controller
- EtherCAT P
- Accessory
Description
On-wall humidity and temperature sensor
HYGRASGARD® AFTF-35
Condensation-protected on-wall sensor HYGRASREG® AFTF-35 with active and switching output, housing made
of impact-resistant plastic with quick-locking screws, cable gland, plastic sinter filter (replaceable), optionally
with/ without display, for detecting relative humidity (0…100 % RH) and temperature (4 switchable measuring
ranges, max. 0...+100 °C) as well as for determining various parameters of humidity measurement technology.
The measuring transducer converts the measured variables into a standard signal of 0 - 10 V or 4…20 mA.
The unit is specially designed for use in the high humidity range (95…99 % RH). A long-term stable, digital
humidity and temperature sensor is used. Overtemperature prevents or hinders dew formation on the humidity
sensor. A second, separate temperature measuring element is used to determine the actual relative humidity
of the ambient air. The following measured variables are calculated internally from these parameters and are
retrievable via output OUT3: absolute humidity, mixing ratio, dew point and wet bulb temperature (can be
changed via DIP switch).
The sensor is used in medical technology, refrigeration technology, control technology, air conditioning and clean room technology. The sensor is factory-calibrated; an environmental precision adjustment by an expert is possible.
The sensor is used in medical technology, refrigeration technology, control technology, air conditioning and clean room technology. The sensor is factory-calibrated; an environmental precision adjustment by an expert is possible.
Technical details
Voltage supply
24 V AC/ DC (± 10 %)
Power consumption
typically < 6 W at 24 V DC, peak current 200 mA
Data points
Temperature [°C], relative humidity [% RH], absolute humidity [g / m3],
dew point [°C], mixing ratio [g / kg], wet bulb temperature [°C]
dew point [°C], mixing ratio [g / kg], wet bulb temperature [°C]
Working resistance
> 100 kOhm for U -variant; 100...500 Ohm for I -variant
Measuring range, humidity
0...100 % r. H.
Deviation of humidity
typisch ± 3,0 % (30...70 % RH) bei +25 °C, sonst ± 3,5 % (Abweichung der alternativen Kenngrößen ergeben sich aus den Abweichungen von Feuchte und Temperatur.)
Measuring range, temperature
Multirange switching with
4 switchable measuring ranges (see table)
0...+50 °C (default); -20...+50 °C; -20...+80 °C; 0...+100 °C
Temperature deviation
typically ± 0.5 K at +25 °C
Warm up time
< 10 min
Response time
< 60 s
Sensor
digital humidity sensor
with integrated temperature sensor,
low hysteresis, high long-term stability
with condensation protection by heating function (plus a second, separate temperature measuring element)
with integrated temperature sensor,
low hysteresis, high long-term stability
with condensation protection by heating function (plus a second, separate temperature measuring element)
Sensor protection
plastic sinter filter, Ø 16 mm, L = 35 mm, exchangeable
(optional metal sinter filter, Ø 16 mm, L = 32 mm)
(optional metal sinter filter, Ø 16 mm, L = 32 mm)
Measuring ranges
0...+50 / –20...+50 / –20...+80 / 0...+100 °C
0...100 % RH
0...100 % RH
Ambient temperature
storage –20...+50 °C; operation –20...+50 °C
Process connection
By means of screws
Protective tube
made of stainless steel V2A (1.4301), Ø 16 mm, NL = 55 mm
(combined humidity and temperature measuring element) and
of stainless steel V4A (1.4571), Ø 6 mm, NL = 65 mm
(via a second, separate temperature measuring element)
Electrical connection
3- or 4-wire connection
0.14 - 1.5 mm² via plug terminals
0.14 - 1.5 mm² via plug terminals
Housing
plastic, UV-stabilised,
material polyamide, 30 % glass-globe reinforced,
with quick-locking screws
(slotted/ Phillips head - combination),
colour traffic white (similar to RAL 9016),
housing cover for display is transparent !
material polyamide, 30 % glass-globe reinforced,
with quick-locking screws
(slotted/ Phillips head - combination),
colour traffic white (similar to RAL 9016),
housing cover for display is transparent !
Cable gland
M 16 x 1.5, including strain relief, exchangeable,
max. inner diameter 10.4 mm
max. inner diameter 10.4 mm
Dimensions
126 x 90 x 50 mm (Tyr 2)
Installation
vertical mounting, humidity sensor at the bottom
Long-term stability
± 1 % per year
Permissible air humidity
< 99% r.H. pollutant-free, non-precipitating air
Protection class
III (according to EN 60 730)
Protection type
IP 65 (according to EN 60 529) in the built-in state,
Housing tested, TÜV SÜD, Report No. 713139052 (Tyr 1)
Housing tested, TÜV SÜD, Report No. 713139052 (Tyr 1)
Protection type housing
IP 65
Standards
CE conformity
according to EMC Directive 2014/ 30/ EU,
according to EN 61 326
according to EMC Directive 2014/ 30/ EU,
according to EN 61 326
Function
Due to a constant overtemperature of the humidity sensor, its dewing is significantly impeded or prevented within the system limits.
A faster reaction speed to humidity fluctuations is achieved, even in the range above in the range above 95 % RH. The sensor (combined humidity and temperature measuring element) is heated approx. 3 K above the ambient temperature. From the measured relative humidity at overtemperature, the chip temperature of the sensor and the ambient temperature (via a second, separate temperature measuring element) the actual relative humidity is determined.
A faster reaction speed to humidity fluctuations is achieved, even in the range above in the range above 95 % RH. The sensor (combined humidity and temperature measuring element) is heated approx. 3 K above the ambient temperature. From the measured relative humidity at overtemperature, the chip temperature of the sensor and the ambient temperature (via a second, separate temperature measuring element) the actual relative humidity is determined.